Search Results

An experimental and analytical study was conducted to investigate the effects of load control with port throttling on stability and fuel consumption at idle. With port throttling, the pressure in the intake port increases during the valve-closed period due to flow past the throttle. If the pressure in the port recovers to ambient before the valve overlap period, back flow into the intake system from the cylinder is eliminated. This allows increased valve overlap to be used without increasing the residual mass fraction in the cylinder. Results showed that, with high valve overlap and port throttling, idle stability and fuel consumption can be maintained at values associated with low overlap in a conventionally throttled engine. However, implementation of this concept in production is regarded to require precision-fit and balanced port throttles, an external vacuum pump for vacuum systems support, and revision of the PCV system.

The aldehyde emissions of 1.6L and 5.0L flexible fuel vehicles (FFV) have been measured, with and without a catalyst, on a range of fuels. The “zero mile” catalyzed emission levels of formaldehyde when operating on M85 (85% methanol and 15% gasoline) are in the 5-15 mg/mi range, but as mileage accumulates they tend to be in the 30-50 mg/mi range. The feedgas levels are high and appear to correlate with engine displacement. The formaldehyde and methanol emissions are higher when operating on M100, compared to M85, but the non-oxygenated hydrocarbon emissions are about the same for both fuels, which suggests that the use of M85 may actually provide more air quality benefit than M100. High mileage control of aldehydes to the level of gasoline vehicles does not appear possible with current technology.

The proliferation of Unibody construction, for vehicle weight reduction, and the expanded use of precoated steel, for improvement in outer body rust-through protection, has significantly increased the number of bimetallic and crevice unions on U.S. manufactured vehicles. Cyclic corrosion and proving ground testing has shown that these unions are highly active electrochemically, resulting in extensive anodic corrosion and cathodic de-lamination of the paint film. This work examines the individual contribution of each layer of the applied protective coatings package, with respect to applied film thickness, to the reduction of permeation by water, oxygen, and NaCl and resultant corrosion.

With the increasing emphasis on and importance of aerodynamics on vehicle fuel economy and handling, conservative approaches to sizing front-end cooling openings based on projected radiator area need to be replaced by a performance-based method. The method would not only allow more flexibility in front-end styling, but would enable the design of the grille, cooling hardware and vehicle heat rejection requirements to be based on the cooling performance of the total vehicle. The reductions in cooling drag and front lift from smaller, but more functional, grille openings would improve vehicle fuel economy and handling. A performance-based front-end design approach is described in the paper along with some selected experimental results. The method is based on an experimental technique for simultaneously measuring the total radiator airflow and vehicle aerodynamic performance in an aerodynamic wind tunnel.

Ford's continued effort to improve fuel economy in automotive applications has emphasized the need for lightweight components that retain all the toughness associated with Ford truck vehicle characteristics. The application of an impact extrusion process to wheel design and manufacture, for Ford Aerostar, provides strength, performance and style more efficiently than other traditional processes. It results in a valuable 33% weight saving over comparable HSLA steel wheels, and provides the customer with uncompromised value. The Ford Aerostar Impact Extruded Aluminum Wheel was designed to be of one-piece construction, manufactured from a less than 1″ thick aluminum wafer-shaped blank. The process permits manufacture in half the steps of a conventional stamped steel wheel, and eliminates extensive machining required with forged or cast aluminum wheels.

Successful application of turbocharger technology to the Ford 2.3L OHC engine requires management of thermal loading. The 1979/1980 2.3L draw-thru carbureted engine was octane and spark advance limited, requiring calibration to worse case 91 RON conditions. Since no adaptive calibration control was possible relatively late ignition timing compromised engine performance. To improve performance, driveability, fuel economy and emission control, work was initiated in mid 1980 on a blow-thru electronic fuel injected engine scheduled for 1983½ production. Program assumptions were issued specifying a tuned EFI blow-thru inlet system, exhaust manifold mounted AiResearch T03 turbocharger with integral wastegate and 8.0:1 compression ratio with a dished piston. Also included were base engine revisions to accommodate increased thermal and mechanical loads.

Recent fuel cost increases have changed engine cost/benefit design guidelines and, therefore, renewed interest in engine friction reduction. At a typical part throttle engine operating condition, the mechanical friction (including oil pump & water pump) of a conventional four-cylinder engine consumes approximately 22% of the indicated power. A1 psi (6.9 kPa) MEP reduction in mechanical friction can result in an EPA, M-H fuel economy improvement of l%-2%, depending on the engine/vehicle configuration. This paper reviews various friction measurement methods and presents motoring friction data for several small engines (four and six cylinder). The friction of various components, including the valve train, pistons, rings and rods, seals and engine auxiliaries (alternator, water pump and oil pump) are also shown. Component design modifications for reducing friction are discussed, and projections and measurements of fuel economy gains for improved components are presented.

The effect of coupling chassis dynamometer rolls (front to rear) on city and highway fuel economy and emissions was investigated. A representative fleet of ten Ford certification vehicles (five passenger cars and five trucks) was tested in coupled and uncoupled roll configurations. Testing was conducted on a Clayton CTE-50 dynamometer with a hydrokinetic power absorption unit (P.A.U.) which was calibrated at a single point (50 mph). It was found that emission levels increased significantly (95% confidence level) for all constituents except city-NOx, which demonstrated mixed results. Observed fuel economy was reduced for both city and highway (3.6% and 4.0%, respectively, for a combined Metro/Highway (M/H) reduction of 3.8%) when the rolls were coupled.

Ford's new 2.3 Litre I-4 Turbocharged Engine and Powertrain was specifically developed to match the new 1979 Mustang/ Capri. This engine/vehicle combination was developed to provide the customer excellent vehicle performance, good fuel economy and driveability. Extensive vehicle and dynamometer work was done to match the turbocharger to the engine and optimize in-vehicle mid-range to high end performance. The relatively high compression ratio (9.0:1) was retained from the naturally aspirated engine to preserve low end manual transmission vehicle performance before turbocharger boost. Revisions to basic engine components and structures to insure durability will be discussed.

A vehicle fleet test has been conducted to determine if octane advantages due to selected cooling system variables persist with stabilized deposits. The variables tested were reduced coolant temperatures, a direct substitution of aluminum for the iron cylinder head and an aluminum head with Unique Cooling. Octane requirements, octane requirement increase (ORI), emissions and fuel economy results are presented and discussed. Engine tests to determine the sensitivity of octane to independently controlled engine temperatures confirmed the primary dependence upon coolant temperature. Additional tests identified some of the variables which cause octane differences among the cylinders of one engine and between engine families.

The performance of three way and NOx catalysts was evaluated on vehicles utilizing non-feedback fuel control and electronic feedback fuel control. The vehicles accumulated 80,450 km (50,000 miles) using fuels representing the extremes in hydrogen-carbon ratio available for commercial use. Feedback carburetion compared to non-feedback carburetion improved highway fuel economy by about 0.4 km/l (1 mpg) and reduced deterioration of NOx with mileage accumulation. NOx emissions were higher with the low H/C fuel in the three way catalyst system; feedback reduced the fuel effect on NOx in these cars by improving conversion efficiency with the low H/C fuel. Feedback had no measureable effect on HC and CO catalyst efficiency. Hydrocarbon emissions were lower with the low H/C fuel in all cars. Unleaded gasoline octane improver, MMT, at 0.015g Mn/l (0.06 g/gal) increased tailpipe hydrocarbon emissions by 0.05 g/km (0.08 g/mile).

A fundamental thermodynamic model of the complete spark-ignited, homogeneous charge engine cycle has been used in several parametric analyses to predict the effects of engine design and operating alternatives on fuel consumption and emissions of NOx and unburned hydrocarbons (HC). The simulation includes sub-models for wall heat transfer, NOx and HC emissions, and the engine breathing processes. This work demonstrates the power and utility of a comprehensive engine simulation by presenting several independent parametric studies that were carried out in response to genuine engine design and/or operating strategy questions. Included in this compilation are the effects of cycle heat loss, exhaust port heat loss, combustion duration, and charge dilution (EGR and/or lean air-fuel ratio). In addition, the influence of the design variables associated with bore-stroke ratio, intake and exhaust valve lift, and cam timing are considered.

The emission index (grams of species per kilogram of fuel) field within a regenerative turbine combustor has been mapped using a water-cooled sampling probe. The probe employed a choked orifice to simultaneously determine the local temperature. Derived from measurements are: air-fuel ratio, combustion efficiency, average fuel velocity and fuel distribution factor. Methods of averaging the discrete data are developed. A comparison of the data obtained when the combustor was operated on each of two fuels revealed that the use of methanol leads to lower nitric oxide but higher carbon monoxide emission than does the use of diesel fuel.